Anycom PM-300 Instruction Manual download pdf (Page 3)

Reflex 300™ Breaker Reset & Lamp Replacement

Caution: Always replace with the exact same type lamp, unless oth-

erwise specified by an authorized American DJ

® technician. Replace

with anything other than the specified part can damage your unit and

will void your manufactures warranty.

Warning: If after you have replaced the lamp or reset the breaker

and you continue to blow either one, STOP using the unit. Contact

customer support for further instructions, you may have to return the

unit for servicing. Continuing to use the unit may cause serious dam

age.

Breaker Reset: This unit is equipped with a built-in safety breaker.

This breaker is designed to close the power circuit in the event of an

internal short or power surge. This will reduce the risk of electrical

shock or ﬁre and protect the circuitry. To reset the breaker, push the

breaker button in until you hear it “pop” back in to place. If the break

er continues to pop, stop using the unit and contact our customer

support team, the unit may need to be returned for service

Lamp Replacement: Caution! Never open the unit when in use.

Always disconnect the main power and allow the fixture ample time

to cool before attempting to replace the lamp. Lamp replacement has

been made simple by incorporating a remove tray that is retained by

a single thumb screws. Again, please remember to always replace

with the exact same type lamp.

1. Be sure to follow the proper procedures when handling halogen

lamps. Never touch the new lamp with your bare fingers.

2. Unscrew the single thumb screw located on the rear of the unit.

3. Once the thumb screw has been remove, pull back the lamp

assembly cover plate to expose the lamps.

4. Remove and replace the lamp with an exact match.

5. Reassemble in reverse order.

©American DJ® - www.americandj.com - Reﬂex 300™ Instruction Manual Page 6©American DJ® - www.americandj.com - Reﬂex 300™ Instruction Manual Page 5

Halogen Lamp Warning! This fixture is fitted with

halogen lamps which are highly susceptible to dam

age if improperly handled. Never touch the lamps

with your bare fingers as the oil from your hands will

shorten lamp life. Also, never move the fixture until

the lamps have had ample time to cool. Remember,

lamps are not covered under warranty conditions.

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal lenses and dichroic colored dishes should be carried out periodi

cally to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a soft brush to clean out the cooling vents

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-

mend cleaning on a monthly basis. Periodic cleaning will ensure lon

gevity, and crisp beam output.

Reflex 300™ Cleaning

Trouble Shooting:

Listed below are a few common problems and solutions you should

try before contacting customer support. For all other issues please

contact customer support.

Unit rotates but has no light output from the unit;

1. Be sure you have connected your unit into a matching wall outlet.

2. Remove the lamp cover and be sure the lamps are seated in their

sockets properly. Occasionally lamps become loose during ship-

ping be sure the lamps are push in to their sockets all the way.

3. Be sure the lamps are good.

Heads do not rotate and lamps do not turn on;

1. Be sure you have connected your unit into a matching wall outlet.

2. Be sure the external breaker has not blown. The breaker is

located on the bottom panel of the unit.

3. Be sure the unit power cord is properly seated in the power outlet

and the outlet has power.

Reflex 300™ Trouble Shooting

1 2 3 4

Comments to this Manuals

No comments

Anycom PM-300 Instruction Manual Page 3

Comments to this Manuals